top of page

Has Your Crane Been Sitting Idle? What CSA B167:26 Says Before You Use It Again

Nov 1
4 min read

Many shops in Saskatchewan have one: the crane over the back bay that only gets used a few times a year, or the hoist in a building that was shut down for a season. When it's time to lift again, the big question is simple. Can you just push the button?

Under the updated CSA B167:26 standard, the answer depends on how long the crane has been idle and what service class it is. Here's a plain-language guide.

Idle time counts, not just calendar time

CSA B167:26 already sets regular inspection intervals by crane class (Table 2). Clause 6.1.4 adds a rule for equipment that has gone longer than those intervals without being used or inspected. In that case, the crane has to be inspected according to Table 3, based on its class and how long it has been inactive.

In short, a crane that sat unused doesn't get a free pass because it "hasn't been working." Moisture, corrosion, seized brakes and dried-out lubrication can all develop while a crane sits.

How long is too long? (Table 3)

Unless an engineer directs otherwise, Table 3 sets out the inspection needed after a period of inactivity:

  • Class A (standby or infrequent service): 6 months to 1 year idle needs a frequent inspection. 1 to 2 years needs a periodic inspection.

  • Class B (light service) and Class C (moderate service): 1 month to 1 year idle needs a frequent inspection. 1 to 2 years needs a periodic inspection.

  • Class D (heavy service): 1 to 6 months idle needs a frequent inspection. 6 months to 2 years needs a periodic inspection.

  • Class E (severe service): 1 week to 3 months idle needs a frequent inspection. 3 months to 2 years needs a periodic inspection.

  • Class F (continuous severe service): 1 day to 3 months idle needs a frequent inspection. 3 months to 2 years needs a periodic inspection.

  • Unclassified or special service: as recommended by the manufacturer or an engineer.

A frequent inspection (clause 6.4.1.1) checks the crane for defects, malfunctions and damage, including watching it in operation. The visual and audible checks are recorded in the maintenance log book by a competent person.

A periodic inspection (clause 6.5.1.1) is a visual and audible examination by a crane inspector, with a record kept. For Class A, B and C cranes, that's the annual inspection.

The two-year line: "out of service"

This is the one that catches people. Clause 6.1.4 says a crane or hoist that hasn't been used or inspected for more than two years is considered out of service. Before it goes back to work, it must be recommissioned, or re-inspected and tested as recommended by an engineer.

There's an important exception in the notes to that clause. A crane that sat unused but was still inspected to the standard before the end of the two-year period is not considered out of service. That's a strong reason to keep standby cranes on their regular inspection schedule even when nobody is using them, so they never need a full recommissioning.

What about Saskatchewan law?

The Saskatchewan Occupational Health and Safety Regulations, 2020 (Part 13, Hoists, Cranes and Lifting Devices) apply too:

  • Section 13-18(1) requires a competent person to inspect a hoist, crane or lifting device before it's used at the start of each work shift, and at regular intervals recommended by the manufacturer.

  • Section 13-19(1) says that if an inspection turns up a condition that might make the equipment unsafe, it can't be used until the necessary repairs are done.

  • Section 13-17(1) requires a log book for each hoist and crane rated over 5 tonnes, recording hours of service and all inspection, maintenance and calibration details.

CSA B167:26 lines up with this. Clause 6.7 says hazards found during checks and inspections must be corrected before the equipment is placed into service, unless an engineer or other competent person approves an exception in writing. Clause 6.6 asks owners to keep both an operator daily log book and an inspection, maintenance and repair log book, available for review for the life of the equipment.

Does it need a load test?

Not automatically. Under clause 7.3.1, load tests are required before use for new, re-installed or modified cranes and hoists. For a crane that has simply been idle past two years, clause 6.1.4 leaves the testing to what an engineer recommends. If the crane is re-installed (for example, moved to a new building) or modified while it's down, clause 7.3.1 requires a load test before use.

A simple plan for idle cranes

  1. Find the last inspection date in your log book, and check the crane's service class.

  2. Use Table 3 to see whether you need a frequent inspection, a periodic inspection, or recommissioning.

  3. Tag the crane out until the inspection is done and any hazards are fixed.

  4. Record everything in the log book.

  5. Keep standby cranes on their regular inspection schedule so they never cross the two-year line.

We can help

SafeLift Crane Aid (A Division of Venter Cranes), with our head office in Langham SK, serving Saskatoon and all of Saskatchewan, inspects, repairs and recommissions overhead cranes, hoists, gantries, monorails and jib cranes to CSA B167:26 and OEM requirements. We're a Demag Master Distributor for Saskatchewan and an authorized R&M Materials Handling distributor.

Got a crane coming back from a long rest? Book an inspection or ask for a quote:

Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating

Stay in tune. Get 10% off.

Keep informed about the crane & hoist industry with tips, in-depth articles, and updates on safety regulations sent to your email.

​

Receive 10% off your first annual inspection when you switch to us! (Valid for 1 year after subscribing.)

Large crane warehouse

10% OFF
INSPECTION

bottom of page